Welcome To b2b168.com, Join Free | Sign In
中文(简体) |
中文(繁體) |
Francés |Español |Deutsch |Pусский |
| No.13635076

- Product Categories
- Friendly Links
Information Name: | Xin-pump (Figure) _316L Hubei chemical pump chemical pump _ |
Published: | 2015-06-05 |
Validity: | 0 |
Specifications: | Any |
Quantity: | |
Price Description: | |
Detailed Product Description: | IH stainless steel chemical pump installation: First, IH stainless steel chemical pump installation is reasonable, there is a significant impact on the normal operation and service life of the pump, it must be carefully corrected before installation can not be sloppy, shape and dimensions of the pump. Second, we must ensure that the pump at work does not exceed their allowed NPSH. Height (or intrusion height) must be based on NPSH characteristics of the pump, piping and pressure loss characteristics of high temperature water suction pressure to determine the level of the pump suction. 1, the pump suction on the lower usage, should the suction valve on the bottom line tops and set screw or soil liquid outlet valve in the pipeline, in order to prime the pump for use before starting. 2, pump intrusion usage, the suction pipe should be tops valves and filters, to prevent debris from entering. Third, the suction and discharge piping should another stent, not be used as a support. Fourth, the installation location should be convenient mobile inspection and repair. Five, IH stainless steel chemical pump installation sequence: 1, the unit placed on the buried foundation anchor bolts, placed between the base and the base pairs of wedge pad for alignment purposes. 2, release couplings. Respectively, with a spirit level on the shaft or the base, by adjusting the purification pad, looking after the unit level being appropriately tighten the bolt to prevent the move. 3, with the pouring of concrete base and foot screw inspection holes. 4. After the concrete dries, should tighten the bolt, and recheck the shaft of ice roughness. 5, take a good line and determine the future direction of rotation of the prime mover, connect couplings, and then check the concentricity of the shaft again, measuring the coupling outside the park up and down, left and right may not exceed the difference between 0.1mm, two couplings END CLEARANCE proof chemical pump, in a week maximum and minimum may not exceed the difference between the microphone 0.3mm 6, in the actual operation of the unit 3 - 4 hours alkali chemical pumps made after final inspection, if no adverse phenomenon is considered qualified installation. IH stainless steel chemical pump start: 1. Close the inlet pressure (or vacuum) gauge and water valve, if the bypass pipe, this time should be closed. Starter motor (best to jog, after confirmation steering pump correctly, began official operation). Then open the outlet pressure (or vacuum) gauge, when the pump reaches normal speed, and pointed out that the corresponding pressure meter, and then slowly open the water valve vertical chemical pumps, adjusted to the needs of the working conditions. In the case of the discharge pipe is closed, the pump continuous working hours, not more than three minutes. 2, IH stainless steel chemical pump start process should always pay attention to the vibration of the prime mover and pump power readings, the number of vibrations not more than 0.06 mm, the measurement site is chock. 3, IH stainless steel chemical pump seal: The mechanical seal should be no leakage, heat generation, packing ^ I in a continuous trickle state. IH stainless steel chemical pump operation: 1, always check the pump and motor heat (temperature rise should not exceed the bearing 75 ℃) and oil level gauge oil supply situation. Usually after 1500 hours per run, to replace all the lubricant once. 2, can not use the suction valve to adjust the flow to avoid cavitation. 3, IH stainless steel chemical pumps should not be less than 30% of design flow chemical pumps run continuously, if you must run continuously in this condition, you should install a bypass pipe at the outlet of the discharge excess traffic. 4, pay attention to pump operation without noise, such as found in an abnormal state, should be eliminated or stop checking. Xin-pump (Figure) _316L _ Hubei chemical pump chemical pump provided by the Hebei Xin-pump factory. Hebei Xin-Pump Plant (www.shuibeng999.com) (www.shuibeng999.com) is a company specializing in "clean water pumps, sewage pumps, slurry pumps, double suction pumps, chemical pumps, liquid pumps and peripheral products," the company . Since its inception, we adhere to the "good faith, sound management" approach, the courage to participate in healthy competition in the market, so that the "Xin Cheng" brand has a good reputation. We adhere to the "service first, customer first" principle, so that the pump Xin won the trust of customers in all centrifugal pumps, and establish a good corporate image. Special Note: This information is for reference only pictures and information, please contact us to obtain the most accurate information, thank you! |
Admin>>>
You are the 16162 visitor
Copyright © GuangDong ICP No. 10089450, Hebei Xin-pump factory All rights reserved.
Technical support: ShenZhen AllWays Technology Development Co., Ltd.
AllSources Network's Disclaimer: The legitimacy of the enterprise information does not undertake any guarantee responsibility
You are the 16162 visitor
Copyright © GuangDong ICP No. 10089450, Hebei Xin-pump factory All rights reserved.
Technical support: ShenZhen AllWays Technology Development Co., Ltd.
AllSources Network's Disclaimer: The legitimacy of the enterprise information does not undertake any guarantee responsibility